PlumbingStore.com
ordering information shipping information return policy contact us view your shopping cart search our PlumbingStore!

- Takagi TK3-SP tankless water heaters -

If your interested in Takagi T-K3-SP Tankless Water Heater, you may also think of looking at:
go to tankless water heaters index - go to Takagi tankless water heater comparison chart - go to Hot Water Dispensers
go to electric tankless water heaters by Eemax - go to water heater water flex connectors - go to gas-related products
go to stainless steel vent pipe - go to Rheem tankless water heaters - go to accessories for Takagi tankless water heater



Takagi T-K3-SP (TK3SP) - Flash Tankless Gas Water Heater
TK-3-SP tankless water heater
Takagi T-K3-SP
(wall brackets are built onto the unit)
This tankless gas water heater features:
  • Compact water heater with BIG BITE! - The T-K3-SP (TK3SP) measures 20.5" x 13.8" x 8.5" which allows for installation in spaces with limited area or in locations closer to the point of use. This results in less travel-time through pipes, which means less energy is wasted.
  • Save Money - No storage tank to clog with deposits and rust. No pilot light to waste gas. Computer-controlled burners use only the gas required according to demand, which significantly increases efficiency.
  • Giant Flexibility - Capable of handling water flows ranging from .5 to 7.0 gallons per minute, with heating capability of 11,000 to 190,000 BTU, the T-K3-SP has a great range, all controlled by a computer board and sensors checking for flow, temperature and demand.
  • Save Energy - Water is only heated as it is used, without need for a holding tank to waste energy. Computer controlled electronic ignition allows the T-K3-SP (TK3SP) to operate without a pilot light and save up to 50% off utility cost.
  • Peace of Mind - Safety is constantly monitored internally with an advanced system of circuits and sensors checking for over or under-heating, freeze conditions, gas levels, water levels, even air and venting conditions.
  • Added protection - The T-K3-SP (TK3SP) comes equipped with heating blocks to prevent freezing which can damage the heat exchanger. The T-K3-SP also ignites automatically, without the water flow, to prevent freezing the heat exchanger as well. Click here for more information
Since water heating is generally at least 20% of an average American family's energy expenses, efficient gas tankless water heaters can potentially cut your family's total annual energy bills significantly. No more wasting energy due to your water being heated 24 hours per day, 365 days per year. Just heat the water that you need, only when you need it!

Takagi T-K3-SP (TK3SP) low emissions tankless water heater delivers up to 240 gallons of hot water per hour (when raising the water temperature by 77°: From 58° to 135°). No tank means an endless supply of hot water for a house, business or anywhere a constant source of hot water is needed.
We cannot show pricing on the web for these items. To request a price quote, select the items you are interested in by clicking the box in the "Select Item(s)" column next to the product. Click the button below the accessories to add items to your quote list.
Takagi T-K3-SP Water Heaters
click for Takagi tankless water heater comparison chart
Model # Description Select Item(s)
TK-3-SP Natural Gas Tankless Water Heater - Natural Gas, 190,000 max BTU's
TK-3-SP Propane Tankless Water Heater - Propane, 190,000 max BTU's
 
Accessories for Takagi T-K3-SP
Note: Wall brackets are built onto the TK3-SP and do not need to be purchased separately
go to stainless steel venting
Model # Description Select Item(s)
TK-BF01 replaces (TK-TV03) Back Flow Prevention Kit
TK-KPWL4-1 Wall Vent Terminator (Louver) - 4.2" - 6" wall thickness
TK-KPWL4-2 Wall Vent Terminator (Louver) - 5.6" - 9" wall thickness
TK-KPWL4-3 Wall Vent Terminator (Louver) - 8.2" - 14" wall thickness
TK-KPWH4-1 Wall Vent Terminator (Hood) - 4.2" - 6" wall thickness
TK-KPWH4-2 Wall Vent Terminator (Hood) - 5.6" - 9" wall thickness
TK-KPWH4-3 Wall Vent Terminator (Hood) - 8.2" - 14" wall thickness
TK-TV04 Outdoor Vent Cap
TK-RB01 Recess box with vent elbow and vent hood termination
TK-RE02 Remote Control
TM-RE30 Temperature Remote Controller (optional)
TK-PC01 Pipe cover
WS1019 Wall Mount Drain Pan for Tankless Water Heaters
PVC Drain Connector Drain connector for the tankless water heater drain pan (listed above)
Includes 1 each: 1" PVC male adapter, 1/2" bulkhead gasket to fit 1" threads, and 1" galvanized locknut
The standard temperature setting is 122°F and is only adjustable with purchase of the TK-RE10 temperature remote controller.
 
Pressure Relief Valves
A pressure relief valve is required for all tankless water heaters. In some areas, a temperature and pressure relief valve is required. Check your local plumbing code for more information.
Pressure Relief Valve - Brass - 3/4" - 150 PSI
Temperature and Pressure Relief Valve - up to 200,000 BTU
 
"The Isolator" Isolation Valves
Complete inlet/outlet valve system that provides everything you need for a secure installation including full port testing and flushing of the system with easy to install union connections.
Isolation Valve - Set (Hot & Cold) 3/4" IPS Union x 3/4" IPS
Isolation Valve - Set (Hot & Cold) 3/4" IPS Union x 3/4" Sweat
 
"The Isolator EXP E2" Isolation Valves
Complete inlet/outlet valve system that provides everything you need for a secure installation including full port testing and flushing of the system with easy to install union connections. Includes pressure relief valve.
Isolation Valve - Set (Hot & Cold) 3/4" IPS Union x 3/4" IPS
Isolation Valve - Set (Hot & Cold) 3/4" IPS Union x 3/4" Sweat
 
Gas Connectors
Stainless Gasflex - 1" OD (3/4" ID) x 24" - with adapter to 3/4" FIP x 3/4" MIP
Gas Ball Valve 3/4"
 
Water Connectors - click here for more flexible water supply lines
Flexible Corrugated Stainless Steel Water Connector - 3/4" FIP x 3/4" FIP - 18" Long
Flexible Corrugated Stainless Steel Water Connector - 3/4" FIP x 3/4" FIP - 24" Long
Flexible Corrugated Copper / Stainless Steel Water Connector - 3/4" FIP x 3/4" Nom Sweat - 18" Long
Flexible Corrugated Copper / Stainless Steel Water Connector - 3/4" FIP x 3/4" Nom Sweat - 24" Long
 
Hot Water Heater Scale Inhibitor System
Features: inhibits scale build-up, helps protect piping from corrosion, maintains efficiency & extends life of system, 3/4" NPT, 6 GPM, cold water feed line, made from FDA CFR-21 compliant materials, suitable for drinking and cooking water and all food applications, and effective on all types of hot water systems-boilers, tankless, and tank-type (gas or electric). Replacement cartridges (AP431) are available for these in-line scale inhibitor systems.
Hot Water Heater Scale Inhibitor System
Replacement filter for hot water heater scale inhibitor system
Note: Recommended time to change/replace filter cartridge is 6 months.
Purchase a replacement cartridge to have on hand when needed.
 
FloodStop Systems for Water Heaters
Automatically shut off the water supply to the water heater and sounds an alarm, leaving all other household fixtures and appliances operational. Powered by AC Adaptor/Transformer or Batteries. Output contacts available, which allow the Controller to connect with Alarm, Home Automation or Auto-Dialer systems if desired. Easily installed in fifteen minutes. 1-Year Manufacturer's Warranty.
FS 3/4-NPT - 3/4" Pipe threaded - full-port motorized ball valve (brass)
- Works with any 3/4" MIPT supply line
FS 3/4-C - 3/4" Compression - full-port motorized ball valve (brass)
- Works with any 3/4" copper applications

Save money and get a quick price quote ... it only takes a minute and is well worth it!!!
Unlike most other products, we cannot show our low pricing on the web for these items.
To request a price quote, simply select the items you are interested in by clicking the box in the "Select Item(s)" column next to the product.
Then click the button below to add the item/s to your quick quote request list.

go to stainless vent pipe


Takagi T-K3-SP (TK3SP) - Specifications
Dimensions (H x W x D) 20.5" x 13.8" x 8.5"
Net Weight 40 lbs.
Power input (BTU) NG 11,000 - 190,000
LP 11,000 - 190,000
Thermal Efficiency NG 82.3%
LP 83.8%
First Hour Rating 240 gallons per hour
Gas Connection 3/4" Male NPT
Water Connection 3/4" Male NPT
Water Pressure Min: 15 PSI, Max: 150 PSI
NG Inlet Pressure Min: 5.0" w.c. Max: 10.5" w.c.
LP Inlet Pressure Min: 8" w.c. Max: 13.5" w.c.
Minimum Flow to Activate Burners 1/2 GPM
Vent pipe size 4" round power vent
3" round intake vent
60°F Temp. Rise 5.2 GPM
70°F Temp. Rise 4.5 GPM
80°F Temp. Rise 3.9 GPM
90°F Temp. Rise 3.6 GPM
Electric Supply 120 V 60 Hz
Inlet Water Temperature 60°F
Outlet Water Temperature 130°F

high output tankless water heater chart
Be sure to install only code approved power vent piping.

Venting and Combustion
  • 4" category III stainless steel
  • Vertical or horizontal installation
  • 50' max length, 5 elbows max (90° elbows = 5' equivalent length)
  • Power vent
  • Electronic ignition
  • 3" combustion air intake

go to other tankless heaters Frequently Asked Questions


Most Frequently Asked Questions

Takagi tankless water heater"What type of vent do these tankless water heaters require?"
Takagi tankless water heater These tankless water heaters require Category III stainless steel vent only.

instant water heaters "Will an instantaneous water heater save me money on my utility bills?"
instant water heaters Yes, in most applications you will see a savings. There are some variables that could reduce the amount you save. One example is you will not run out of hot water, so longer showers could cut into your savings. Also, the cost of electricity, propane and natural gas in your area will affect the amount of money saved. The higher the cost for the energy type used to heat your water, the quicker you will recover the higher initial cost of installing a tankless versus tank style water heater.

Positives:

  • You will never run out of hot water. "You want an hour long shower? No problem!"
  • Electric units can be installed at the point of use.
  • You're not paying energy costs to heat water 24 hours a day.
  • They're easy to install.
  • Our electric units don't require a T&P valve. (No tank!)
  • Installing a tankless water heater will indeedbe a bonus to the environment (why should we choose wastefulness when we're talking about finite natural resources)?

Negatives:

  • They all need a minimum flow rate & pressure to turn on.
  • The faster water flows through them, the lower the temperature rise. So, if you expect to take a shower while the clothes washer is running, you will need to select a unit sized to your hot water flow requirements. (Gas units handle this a little better than electric models)
  • Electric units need heavy gauge wire. Example: the 9.5kw must have 8ga wire and a 50amp breaker.
  • Gas units need a much larger, special flue pipe and larger gas supply than a conventional water heater.
  • At times they can produce very hot water. It's easier to get scalded.
  • Gas units are more complicated than a conventional water heater.
  • With some brands, parts are hard to find (not a negative if you originally purchase from us, as we like to carry parts for the units that we sell).

Summary:
Tankless water heaters have their place. They're not "the answer" to every hot water need, but if they're used correctly they can be the solution to many of them.

information about instant water heaters "What's the difference between a conventional flue and a direct vent?"
education and frequently asked questions about conventional flue & direct vent A conventional flue is what most people are familiar with. It typically consists of a double-wall flue pipe going from the top of the heater through the roof, venting outside. The fixture draws its combustion air from the space around it (utility room, garage, hallway, etc.). A direct-vent unit vents and draws its combustion air through a specially designed pipe from the outside via an adjacent wall.

information about many companies selling heaters "There are many companies selling all kinds of tankless water heaters. Why should I buy a Takagi tankless gas water heater from you rather than elsewhere?"
education and frequently asked questions about tankless heaters We are a large, reputable company that was here yesterday and we will be here tomorrow. We are often copied, but we don't believe that any one can match our service and certainly our base of satisfied customers is larger than any Internet plumbing supplier since 1995. We sell 1000's of other quality plumbing products as well, so you can rest assured that we know plumbing products. We are a very stable and reputable company. We love to sell what we believe in, and we definitely believe in Takagi.

information about tankless water heaters "If these units don't have a tank, how do they know when to turn on?"
education and frequently asked questions about instant water heaters These tankless water heaters have a flow switch built into them. When you turn on the hot side of a faucet the water begins moving. Once the water is traveling at minimum flow rate for the heater, the flow switch will turn on the gas or electricity.

questions about converting natural gas to propane gas "I would like to convert my natural gas tankless heater to be able to use LPG (propane) gas instead. Do you offer a conversion kit?"
answers about converting natural gas.. no Sorry, but we don't. Even if we could, we probably wouldn't, as in most cases it is not a good idea to convert one type of gas for another. Burners can be different, orifices, etc. Not only is the BTU rating different for these two gases, but also the heat of the flames and a number of other factors. We simply do not wish to sell ("profit from") something that might create a non-safe environment.

information about Takagi temp. rise "Your products specify the 'temp. rise' based on the GPM flow; what do you mean by this?"
education and frequently asked questions about temperature rise Temperature rise is the amount the heater raises the temperature of the incoming water, based on the flow rate shown of that water.

information about tankless water heaters "Is it possible to drain a tankless water heater to prevent freeze damage when not in use?"
education and frequently asked questions about instant water heaters Simple answer: yes, BUT The T-K3-SP (TK3SP) unit comes equipped with heating blocks to prevent freezing which can damage the heat exchanger. The T-K3-SP also ignites automatically, without the water flow, to prevent freezing the heat exchanger as well. The freeze protection system will activate when the temperature drops below 36.5°F and is rated to protect the unit down to -22°F in a wind-free environment. If you will not be using your heater for a long period of time or if the temperatures (including wind chill) drop below -22°F; Simply drain both lines 'to' and 'from' the unit. As long as there are no check valves in the way, that should drain the water from the unit. To guarantee that there is no water in the unit, we recommend two drain valves - one before and one after the unit - as well as blowing air through the water line.

question about hot water heater scale inhibitor system "Will the Hot Water Heater Scale Inhibitor System change the taste or odor of water?"
system extends life No. The active ingredient is colorless, tasteless, and odorless when used as recommended.

question about hot water heater scale inhibitor system "How does the Hot Water Heater Scale Inhibitor System prevent corrosion?"
system extends life It forms a thin protective layer on the inside of pipes and metal parts. This film or layer is microscopic in thickness and will not build up over time.

question about hot water heater scale inhibitor system "What are the best reasons to install a Scale Inhibitor System?"
system extends life Inhibiting helps protect the system by reducing scale buildup and adding to the longevity of the heater.

question about hot water heater scale inhibitor system "Is the Hot Water Heater Scale Inhibitor System's active ingredient safe?"
system extends life Yes! All ingredients used are 100% pure food grade materials. They are approved by the USDA and meet purity requirements as a food additive by the World Health Organization.

question about hot water heater scale inhibitor system "What happens if you don't change cartridges often enough on the Scale Inhibitor System?"
system extends life The original water condition and problem will reappear. Hardness will begin to build up again, which you want to avoid.


read many interesting quotes, such as:
"The wheel of fortune turns round incessantly, and who can say to himself, I shall to-day be uppermost." - Confucius

We hope that we have helped you with Takagi TK3-SP tankless water heaters at PlumbingStore.com.



Search THE Internet Plumbing Store for more:

Alphabetical Product Listing:  A B C D E F G H I J K L M N O P Q R S T U V W X Y Z


go to contact us | go to our welcome page | go to faq's
go to privacy guarantee | go to return policy | go to view cart
The most convenient mail-order Plumbing Store.