Pipe and Nipple Sizing

go to general plumbing information - go to size chart for pipe thread
go to PVC fittings - go to PVC SpaFlex pipe
go to PVC nipples - go to chrome fittings & nipples - go to regular brass nipples

The outside diameter (o.d.) shown is for standard IPS, Schedule 40, pipe (PVC, stainless, brass, steel, etc.)
(not for CPVC, PEX, PB or copper pipe)

Standard nipples and pipe sizing:
Pipe Size	Outside Diameter (O.D.)	Circumference	Threads Per Inch
1/8"	0.405"	1.272"	27
1/4"	0.540"	1.696"	18
3/8"	0.675"	2.121"	18
1/2"	0.840"	2.639"	14
3/4"	1.050"	3.299"	14
1"	1.315"	4.131"	11 1/2
1 1/4"	1.660"	5.215"	11 1/2
1 1/2"	1.900"	5.969"	11 1/2
2"	2.375"	7.461"	11 1/2
2 1/2"	2.875"	9.032"	8
3"	3.500"	10.995"	8
4"	4.500"	14.137"	8
5"	5.563"	17.476"	8
6"	6.625"	20.812"	8
8"	8.625"	27.095"	8
10"	10.750"	33.771"	8
12"	12.750"	40.054"	8

Circumference = distance around the outside of pipe

Click to view items in your shopping cart

Pipe sizes do not refer to any physical dimensions. The outside diameter of each pipe must be measured for size identification. For example, a 3/4" NPT pipe thread has an outside diameter of 1.050 inches. Each thread size has a defined number of threads per inch (TPI). The 3/4" NPT pipe thread has 14 threads per inch. Both the TPI (threads per inch) and OD (outside diameter) of the thread are required for positive identification of thread size because several sizes have the same TPI.

All pipe thread types used in plumbing are specified by the American National Standard for pipe as accredited by the American National Standards Institute (ANSI).

National Pipe Threads (NPT) have tapered threads. These are the most common threads used for general purposes. NPT threads are used for joining and sealing pipe to fittings in low pressure air or liquids and also mechanical applications. The tapered thread is 3/4" over one foot of length. Tapered threads are deeper at the end of the pipe and are increasingly shallower the further they are from the end of the pipe. The taper on the pipe only allows the pipe to screw inside the fitting until it is forced to stop because of the taper. The distance the pipe can be screwed into the fitting is specified by the ANSI standard. After tightening with a wrench the threads may have slight spaces between the pipe and fitting which could cause a leak so a pipe sealant must be used to ensure any gaps are filled.

The Dry-seal thread (NPTF) also have tapered threads. NPTF threads are used when the application is such that pipe sealing compounds may fail due to higher heat or pressure than normal NPT threads can withstand. The threads are designed to seal mechanically by slightly, but sufficiently, crushing the threads when tightened with a wrench. This allows for joining the pipe and fitting without sealants.

The NPT and NPTF threads are interchangeable with sealants such as PTFE tape. None of the other thread standards are interchangeable. Female NPT threads can be designated as "FPT" and male NPT threads can be designated as "MPT."

National Standard Free-Fitting Straight Mechanical Pipe Threads (NPSM) have straight threads which are only used for joining. A washer or gasket is needed to seal this type of threaded connection.

Three less common threads exist, the Garden Hose Thread (GHT), Fire Hose Coupling (NST) and British Standard Taper Pipe Thread (BSPT).

Definition of pipe thread acronyms
NPT	National Pipe Thread
FPT	Female Pipe Thread
MPT	Male Pipe Thread
PTF	SAE short taper pipe thread - dryseal
NPTF	American National taper pipe thread for dryseal pressure-tight joints
NPSM	American National straight pipe thread for mechanical joints
NPSI	American National straight intermediate pipe thread
GHT	Garden Hose Thread
NST	Fire Hose Thread
BSPT	British Standard taper pipe thread (metric dimensions)

We hope that we have helped you with pipe sizes at PlumbingStore.com

Alphabetical Product Listing: A B C D E F G H I J K L M N O P Q R S T U V W X Y Z